zm11.side, zm12.side zm13.side, zm14.side, zm15.side side mounting bracket oct. 2007 / rev. 1.2 ds-zmxx.side-en / all parameters are specified at 25c ambient unless otherwise noted. the information presented in this document is believed to be accurate and reliable and may change without notice. www.pulspower.com phone + 49 89 9278 0 germany 1/1 1. g eneral d escription b racket f or f lat m ounting this accessory is used to mount dimension power supplies and other dimension units sideways to reduce the installation depth. the two aluminum brackets and the black plastic slide must be remo ved from the units, to allow mounting of the zinc-plated steel bracket. two mounting options are possible: panel mount 35mm din-rail mount 2. d imensions and i nstallation d ata the drawings on the left show the bracket for din- rail mounting. the total installation depth is the b dimension plus 6mm plus the height of the din-rail. in case the unit is panel mounted, the b dimension shows the required installation depth. power supply use bracket a b c length width height bracket weight qs3.xxx zm11.side 89mm 38mm 32mm 145mm 65mm 37mm 140g qs5.xxx zm12.side 104mm 46mm 40mm 145mm 65mm 44mm 160g qs10.xxx zm13.side 104mm 66mm 60mm 145mm 65mm 63mm 180g qt20.xxx zm14.side 124mm 71mm 65mm 145mm 65mm 76mm 195g qs20.xxx zm15.side 124mm 88mm 82mm 145mm 65mm 84.5mm 205g yr2.diode zm11.side 89mm 38mm 32mm 145mm 65mm 37mm 140g yrm2.diode zm11.side 104mm 38mm 32mm 145mm 65mm 37mm 140g uf20.xxx zm14.side 89mm 79mm 64mm 145mm 65mm 76mm 195g cs3.xxx zm11.side 89mm 38mm 32mm 145mm 65mm 37mm 140g cs5.xxx zm11.side 104mm 38mm 32mm 145mm 65mm 37mm 140g cs10.xxx zm13.side 104mm 66mm 60mm 145mm 65mm 63mm 180g
zm11.side, zm12.side zm13.side, zm14.side, zm15.side side mounting bracket oct. 2007 / rev. 1.2 ds-zmxx.side-en / all parameters are specified at 25c ambient unless otherwise noted. the information presented in this document is believed to be accurate and reliable and may change without notice. www.pulspower.com phone + 49 89 9278 0 germany 2/2 3. a ssembly and m ounting i nstructions fig. 3-1 detaching din-rail brackets fig. 3-2 detach slide fig. 3-3 mounting steel bracket detach the two aluminium brackets by removing the four screws with a torx screwdriver (torx 10). save the screws for step 3. remove the plastic lock mechanism by using a flat-blade screwdriver to move the lock downwards while at the same time push the plastic slide upwards. detach the plastic slide. mount the steel brackets with the same screws from the din-rail brackets using caution not to over-tighten the screws! recommended tightening torque is 0.6nm. (5.3lb.in). fig. 3-4 panel mount fig. 3-5 din-rail mount two mounting options: - panel mount - din-rail mount preparation for din-rail mounting: install the two aluminium brackets and the plastic slide (detache d from the unit before) onto the side mounting plant with the additional screws provided. 4. o rder n umbers accessory zm11.side side-mounting bracket kit 145x65x37mm zm12.side side-mounting bracket kit 145x65x44mm zm13.side side-mounting bracket kit 145x65x63mm zm14.side side-mounting bracket kit 145x65x76mm zm15.side side-mounting bracket kit 145x65x84.5mm
|
